国产偷v国产偷v亚洲张丽_五月亚洲丁香_a免费在线观看_欧美日本成人_丝袜中出制服人妻美腿_婷婷好紧好多水国产好硬_九九热精品在线播放_97超级在线人妻资讯_日韩精品视频观看_中文字幕无码笫一页

Explosion proof electrical construction is different from ordinary electrical construction, as it depends on the increased explosion-proof requirements of the environment it is located in. According to national and industry requirements, we refer to an explosive environment where combustible substances such as gases, vapors, mist, or dust form a mixture with air under atmospheric conditions. After ignition, the combustion will be transmitted to the environment where all unburned mixtures are present. An area in which explosive gas or combustible dust environments occur in large quantities or are expected to occur in quantities sufficient to require special preventive measures for the structure, installation, and use of electrical equipment is called a hazardous area. Explosion proof electrical construction refers to a job that meets the qualifications, conditions, and professional personnel of explosion-proof electrical construction, and operates in explosive environments and hazardous areas, with strong professionalism.

The basic knowledge that should be mastered in explosion-proof electrical construction includes the following points:

1、 Classification and grouping of explosive substances, as well as classification, grading, and regional scope division of explosive hazardous areas.

Explosive gases should be classified according to their maximum test safety gap (MESG) or minimum ignition current ratio (MICR), and should be grouped according to ignition temperature; Combustible dust can be divided into two types based on its conductive properties: conductive dust and non-conductive dust. Combustible dust is grouped according to its minimum ignition temperature; Explosion hazardous areas are divided into two categories based on the physical state of explosive substances: gas explosion hazardous areas and dust explosion hazardous areas; According to the frequency and duration of explosive gas environments, hazardous areas are classified into three zones: Zone 0, Zone 1, and Zone 2; According to the frequency and duration of the occurrence of combustible dust/air mixtures, as well as the thickness of the dust layer, they can be divided into three regional levels: Zone 20, Zone 21, and Zone 22;

2、 Selection of explosion-proof electrical equipment in explosive hazardous areas.

The selection principle of explosion-proof electrical equipment is safety, reliability, and economic rationality. The selection should be based on the level of the explosive hazardous area and the category, level, and group of explosive hazardous substances. The specific selection table should refer to the standard AQ3009-2007;

3、 Installation of electrical circuits and explosion-proof electrical equipment in explosive hazardous areas.

The installation methods of electrical circuits in explosive gas environments can be divided into cable wiring and conduit wiring. Electrical circuits should be laid in areas with lower explosion hazards or far away from the release source, avoiding places prone to mechanical damage, vibration, corrosion, dust accumulation, and hazardous temperatures. When unavoidable, preventive measures should be taken. The selected low-voltage cables or insulated wires must have a rated voltage higher than the operating voltage of the line and not lower than 500V. The insulated wires must be laid in conduits, etc. Specific training courses for explosion-proof electrical installation, maintenance, and repair can be attended;

4、 Inspection and maintenance of explosion-proof electrical equipment in hazardous areas.

In order to minimize the risk of ignition of electrical equipment in hazardous areas, initial inspections should be conducted on the devices and equipment before they are put into operation during the completion and handover acceptance of the project; To ensure that electrical equipment is in good condition and can be used in hazardous areas for a long time, continuous supervision and regular inspections should be carried out. Initial and regular inspections should be entrusted to safety production testing and inspection institutions with explosion-proof professional qualifications.

The inspection and maintenance of explosion-proof electrical equipment should be carried out by qualified professionals who meet the prescribed conditions. These personnel should receive business training including various explosion-proof types, installation practices, relevant rules and regulations, and general principles of hazardous area classification. These personnel should also receive appropriate continuing education or regular training, and have relevant experience and trained qualification certificates. Follow up with continuous supervision and regular inspections. Provide reasonable remedial measures and equipment replacement measures for maintenance requirements.

Original article by Shenzhen Zhongnuo Testing Technology Co., Ltd., plagiarism and reproduction by any platform or individual are strictly prohibited!